Shot craft Craft Some effort120 min
Cut a music video to the beat: where every cut should land
Work out seconds per bar, mark the downbeats and place cuts on phrases of 4 and 8 bars, with numbers for 70, 96, 120 and 140 bpm.
Where should the cuts land?
Land the big cuts on the downbeat, the 1 of each four-beat bar, and save the biggest changes for the start of a 4 or 8 bar phrase. A phrase is the stretch of music that feels like one sentence, usually a verse line or half a chorus. Change location, angle or colour there. Inside the phrase, cut on bar lines or leave the shot alone. Many editors then nudge a cut one or two frames early or late. Try both and keep the one that feels right. A cut that sits exactly on the grid can feel stiff, and a cut a few frames off can feel like a mistake, so listen with the picture playing.
Cuts on every beat belong to a drop, not a verse.
What is one bar worth at 70, 96, 120 and 140 bpm?
In 4/4, one bar lasts 240 divided by the bpm, in seconds. Here is each tempo, with one bar, a 4 bar phrase and an 8 bar phrase.
- 70 bpm: 3.43 seconds a bar, 13.7 for 4 bars, 27.4 for 8 bars.
- 96 bpm: 2.5 seconds a bar, 10 for 4 bars, 20 for 8 bars.
- 120 bpm: 2 seconds a bar, 8 for 4 bars, 16 for 8 bars.
- 140 bpm: 1.71 seconds a bar, 6.9 for 4 bars, 13.7 for 8 bars.
One beat is 60 divided by the bpm. At 120 bpm that is half a second, or 12 frames at 24 fps. One bar at 120 bpm is 48 frames at 24 fps and 50 frames at 25 fps. If a drummer played the track live, the tempo may drift, so check the numbers against a real chorus.
What do you need before you start?
You need the final mix of the song, your footage sorted by song section, an editor that takes timeline markers, and about 120 minutes for a three minute rough cut.
- The finished song as a WAV or high quality file, so the tempo cannot change under you.
- Takes labelled verse, chorus, bridge, so you are not hunting for footage mid-edit.
- An editor with markers. DaVinci Resolve is free and does the job.
- Headphones, because a laptop speaker hides the kick.
- A note with the bpm and the bar count of each section.
Use only a song, footage and faces you own or have permission to use. This is not legal advice.
How do you place the cuts, step by step?
Work in this order, and the edit hangs together before you polish anything.
- Find the bpm. Ask the producer, or tap along with the song for 30 seconds.
- Work out seconds per bar: 240 divided by the bpm. Write it on the note.
- Put the song on the timeline and add a marker at the start of each section: intro, verse, chorus, bridge.
- Add a marker every 4 bars inside each section. Play a chorus to check the markers still sit on the downbeat.
- Lay your strongest shots on the phrase markers first. Change setup, angle or location there.
- Fill the phrases, cutting every 1, 2 or 4 bars. At 96 bpm that gives shots of 2.5, 5 or 10 seconds.
- Watch with the sound low, then nudge cuts by one or two frames.
When should you cut against the beat or hold a shot?
Cut against the beat to make a moment uneasy, and hold a shot when the song gives you room. Move one cut half a beat late, on the “and” after beat 4, and the picture seems to stumble. Do it twice in a chorus at most. Do it all the way through and the edit reads as careless.
Through a drop, hold one shot for the full 4 bars and let the sound do the cutting. At 140 bpm that shot runs 6.9 seconds. In a ballad at 70 bpm, let a close-up run 2 bars, about 6.9 seconds, with a slow push-in. A slow push-in beats a gimbal orbit here, because the orbit adds movement the song never asked for.
What goes wrong, and what if you run out of energy?
The usual faults are cutting on every beat for the whole song, giving every shot the same length, and ignoring the lyric when a line needs a longer look. Cuts that drift off the grid mean the tempo is not steady, so re-mark that section by ear.
If the edit stalls, cut the chorus only. At 120 bpm an 8 bar chorus phrase is 16 seconds, so a full chorus of two phrases is 32 seconds. Get that right, then copy its rhythm into the other choruses with different footage. When a cut will not land, cover it with an insert shot such as a hand, a lamp or a window, 1 bar long, and move on.
How do you make it easier next time?
Shoot to the grid. Play the song back on set at its true tempo, so every performance take lines up with the bars, and film each setup one bar longer at both ends so you have room to trim. Write the shot list with durations in bars as well as seconds, for example “close-up, 2 bars, 4 seconds at 120 bpm”. Plan a phrase change, such as a new wall colour or a new lamp, at each 8 bar mark before the shoot day. Then the edit is a matter of matching footage to markers you already know.
Frequently asked questions
How often should a music video cut?
It depends on tempo and mood. At 120 bpm, a cut every 1 to 2 bars gives shots of 2 to 4 seconds. A ballad at 70 bpm can hold a shot for 2 bars, about 6.9 seconds.
Should I cut on every beat?
Only in short bursts. At 140 bpm a beat is about 0.43 seconds, so a 4 bar run of cuts on every beat is 16 shots in under 7 seconds. Use it for a drop or a final chorus.
How do I find the bpm of a song?
Ask whoever made the track, or tap along with it for about 30 seconds in a tap tempo tool. Then put markers every 4 bars across a chorus. If the last one still sits on a downbeat, the number is right.
What if the song has no steady beat?
Cut to the vocal phrases and chord changes instead of bars. Set markers by ear, hold shots longer, and use a slow push-in or a still frame to carry the loose sections.